Using Homey Pro v7.0.0 i was not able to add more zigbee units. Ofter advice I reset the Zigbee network, and then i was able to add devices again. But after 16 devices I cannot add any more. Still have 3 Aquara Temp measurement devices but they is not ‘detected’. Have tried location near homey, but…

Problem solved ! The battery level was to low… It was enough to put the device into pairing mode with 3 blue binks, but not enough to pair. After changing battery all remaining end devices got into the Zigbee network with the parent router of my choice. Now the whole network is well balanced. …

Afaik when running firmware v5 and up, you should pair zigbee devices close to the nearest router device. About the channels: Wifi ch.1 and zigbee ch.13 are too close to one another. I would like to advise to change wifi ch.1 to ch.11. If that isn’t possible, change zigbee channel to 22, 23 or 2…

[image] Peter_Kawa: you should pair zigbee devices close to the nearest router device Not exactly: they should be paired at (or near) their final location.

Great advice, moved the AP with most clients to 13, the lesser AP to 6, and zigbee to 11. very low interference reported in Unifi console But still impossible to add more devices. I observe that the developer panel current command has reverted to IDLE but the pairing screen on my homey app still s…

[image] robertklep: [image] Peter_Kawa: you should pair zigbee devices close to the nearest router device Not exactly: they should be paired at (or near) their final location. That’s exactly what I meant Robert. But you describe it a bit more clear:squinting_face_with_tongue:

It might be a &#%×"> but removing some end devices, and adding some router devices should do the trick. Then you could try to add those end devices, and your new ones again. And then pair them, in Robert’s words, at or near their final location. Athom’s zigbee advice here . Regarding zigbee chann…

Very good advice, I migth blew it all by adding end devices from the same spot. Luckily I think I understand it all, now and will distribute router devices around and add end devices AT it`s location to avoid reaching 15 direct childrens of the coordinator Looking at the current scheme, it looks l…

Well, a good plan I guess, but it’s not working. Adding the Routers is just fine, but impossible to add any Aquara device. Not a single one. Tried both Zigbee channel 11 og 21 ( have no higher in dropdown). The Develco Routers is adding fine, but no other end device is added. This is how it looks …

Well, then I found that several of the Auara Temp monitors is refusing to be added. When trying other I did get all, but 4 Aquaras wount add. They enter 3 blue blink state, but is not added. What can possible be reason to that ? I alway try to add them near the desired router. The topology below is…

During adding, after the 3 blinks, keep pushing the button every 2 seconds, will help also many times.

Zigbee network not acception any more devices?

Questions & Help

Peter_Kawa July 4, 2021, 8:40pm 16

Some Aqara sensors don’t seem to work (very long) with Homey, but do work with deCONZ

Aqara sensors stopped working?

Topic		Replies	Views
Cant add more Aqara devices Questions & Help zigbee	1	645	March 1, 2021
Can´t add any new Zigbee devices Questions & Help	23	4992	August 18, 2023
Zigbee problems with Homey bridge Questions & Help zigbee , homey-pro , homey-bridge	11	1699	January 20, 2022
Zigbee issues with pairing several sensors Questions & Help zigbee , homey-pro	18	1893	November 3, 2023
[HOW TO] Plan and setup your Zigbee network Tutorials zigbee , tutorial , homey-pro , homey-bridge , howto	39	16349	April 25, 2025

Zigbee network not acception any more devices?

Related topics