[App][Pro] dingz (v2.0.10)

dingz for all your things

The dingz Switch is a device that allows you to easily connect wired devices to the Homey Smart Home. Depending on the configuration, it includes switches, dimmers, blinds control, etc and a motion (plus only), brightness and temperature sensor.


Attention:

The v1.3.x branch will no longer be developed and supported


Important note for dingz-app

I have found a bug in the firmware (> v2.1.1).

Please check whether the CORRECT MAC address of the dingz is entered in the “WebUI > System > dingz ID” field. If not, please correct it, because if you do not do this, communication with an MQTT broker, for example, will not work properly.


What is new in version 2?

  • Almost everything, except the definitions of the individual dingzDevice, the rest was rewritten
  • Full support of dingz v2 firmware
  • Implementation of the dingzNet
  • With a few exceptions all dingzSwitch types are now supported
  • The dingzDevice’s are based on the configuration of the respective dingz switch
  • dingzDevice repair implemented
  • New images and icons

What is the dingzNet?

The dingzNet is a transparent IoT/MQTT based communication platform over which the individual paired dingz switch interact with the Homey dingz-app as well as the official iOS/Android dingz-app. This also applies to 3-party api/apps that can be used to control dingz v2, but these have not been tested.


Migration from Homey dingz-app v1.3.x to v2.0.x

The migration should actually be (almost) automatic. The only thing you need is described in the setup.

If you still have problems, the easiest way is to delete the dingzDevice and pair it again. If the problem persists, please contact me via the community.

To check if all flows are still working, I can highly recommend the homey app “Flow Checker”.


Known issues

  • Since the dingzSwitch newly distinguishes “non-dimmable” lights and power socket, the dingzDevice (socket) must be deleted and then re-paired

  • The dingzButton flow card unfortunately could not be saved, this must be reassigned via Replace


Supported Devices

  • dingzSwitch > FW: v2.1.72
  • dingzSwitch plus > FW: v2.1.72

Beta versions are not supported


Setup

  1. Install MQTT broker (see Notes)
  2. Configure MQTT broker user (Default user: dingzNet / password: dingzNet)
  3. Install Homey Simple (Sys) Log (Optional, but recommended)
  4. Install Homey dingz-app
  5. Check dingz > MQTT-Broker app settings and configure if necessary
  6. Important: Restart the dingz app.

Usage

  1. Install dingz switch
  2. Add dingz to the network
  3. Configure dingz with the Webinterface.
    • Add device name
    • Add each button, outputs, motors name
    • Configure all buttons, outputs and motors
    • Test if device is installed correctly
  4. Pair the devices with the homey

Supported dingz types

  • internal
    • dingz > deprecated
    • Sensor
    • FrontLED
  • output (Ausgang)
    • light > (Licht)
    • always > (Immer an)
    • switch > (Steckdose geschaltet)
    • sprinkler > (Bewässerungsventil)
    • fan > (LĂĽfter)
    • pulse > (Pulse)
  • motor (Motoren)
    • blind > (Jalousien)
    • shade > (Markisen)
    • window > (Windows)
    • door > (TĂĽren)

ToDo

Devices

  • garagedoor > (Garagentor)
  • heater > (Heizungsventil)

Flow-Cards

  • carousel

Notes

  • Use only a local MQTT broker, because the dingz do not support mqtts protocol.

  • Basically you can use all MQTT brokers.

  • If you use the Homey MQTT-Broker, then it is sufficient to enter the URL “localhost” or “127.0.0.1” at MQTT-Broker settings, because the rest is done automatically by dingzNet.

  • For all “tekkies” who are interested, I can recommend the MQTT Explorer.

  • If you make changes to the configuration of a dingzSwitch, the dingzNet must also be reconfigured. Unfortunately, this is not yet done automatically, but you can do this via the device repair or by restarting the dingz app.

  • dingz device is deprecated. Since the zone controls require a sensor device, I had to implement a new device. This is identical to the “old” dingz device, just with a “sensor” device class. You can simply replace the dingz device with the new sensor device, readjust the flows, then delete the “old” dingz device and finally restart the dingz app.

  • Important for “Button … is …” where-card. In order to configure a dingzButton the following setting must be made in the (WebUI) dingz > buttons > control.

  • Diagnostic-Reports which are not requested by me will be deleted automatically …Community first…

  • Forum-Topic Since I don’t have a crystal ball, please give me the following information so that I can analyze the problem more precisely.
    – App version:
    – dingzSwitch model:
    – dingzSwitch firmware:
    – Homey model:
    – Homey version:
    – MQTT broker:
    – Broker version:


Thanks

Special thanks to all for the help in testing the new version.


Disclaimer

Use at your own risk. I accept no responsibility for any damages caused by using this app.


Copyright

Copyright 2022, 2024 cFlat-inc.org, Chris Gross

Changelog

Live: v2.0.10

  • Images changed

Test:

For later use…

For later use…

Bonjour,

Suite installation de plusieurs Dingz dans mon appartement je remarque plusieurs choses à améliorer.
Serait-il possible de pouvoir commander un contact d’un autre dingz sans passer par un flow?
Est-il prévu de dissocier les touches pour une configuration plus simple? Elle ne s’affiche que avec les capteurs.
Il serait aussi intéressant d’avoir l’image du Dingz avec l’emplacement de la touche correspondante grisé.

Merci

Veuillez Ă©crire en anglais !!

THX Chris

1 Like

Hello,

Following the installation of several Dingz in my apartment, I notice several things to improve.
Would it be possible to be able to order a contact from another dingz without going through a flow?
Are there any plans to separate the keys for a simpler configuration? It is only displayed with the sensors. Have the 4 outputs and the 4 inputs.
It would also be interesting to have the image of the Dingz with the location of the corresponding key grayed out. It would also be interesting to have an image with detector for the dingz plus.
I can gladly help with tests or the like.

Thank you

Sorry for the delayed feedback, I’m moved to a new apartment

Would it be possible to be able to order a contact from another dingz without going through a flow?

The individual dingz can communicate with each other. see dingz-api

Are there any plans to separate the keys for a simpler configuration? It is only displayed with the sensors. Have the 4 outputs and the 4 inputs.

No, because the device does not represent the sensor, it is the dingz device itself. However, you can describe the individual inputs/outputs for a better overview via the dingz web interface.

Anyway, it is recommended that the dingz device is configured correctly first. Then the homey app imports the configuration automatically during paring.

It would also be interesting to have the image of the Dingz with the location of the corresponding key grayed out.

Unfortunately I can’t, because the buttons can be reconfigured via WebInterface, so I don’t know which button is what anymore.

Thank you for your answers.
I do not understand how to link two Dingz without flow.
It is a shame not to have the 4 outputs but also the 4 push buttons that appear when adding homey.
I’ve noticed something else lately. I only have the standard dingz that shows the temperature on Homey.
Do you also have this?
And is it possible to have a different picture between the dingz plus and standard on homey?

Hi Thilko

I do not understand how to link two Dingz without flow.

This has nothing to do with homey, the communication is based on the dingz-RestApi

It is a shame not to have the 4 outputs but also the 4 push buttons that appear when adding homey.

They are not missing. The outputs are represented by the individual generated switches, lights, blinds. For each button you have to create a flow with a virtual device that calls the action.
Sample:
dingz device button-1 pressed > action-a
Virtual-Device button pressed > action-a

I’ve noticed something else lately. I only have the standard dingz that shows the temperature on Homey.

I know, with the dingz plus the motion detector is displayed. Unfortunately, you can not currently select in the homey-api what should be displayed. As soon as athom makes this possible, I will implement this.

And is it possible to have a different picture between the dingz plus and standard on homey?

No, homey does not allow to change the picture

Hello, will you bring this app to homey cloud (bridge)?

I am not the manufacturer, so in a nutshell NO

I have deployed the new version (v1.2.2) of the dingz app on Test. It includes, in addition to general improvements, the upgrade to SDKv3 and thus compatibility with the new Homey Pro (Early 2023).

This version is no longer compatible with the app version v1.3.x. The version will remain on test for about 1 week, after that it will go live.

The new version (v1.2.2) is now live/productive.

I have now set the test app to live, the individual Dingz devices now need to be deleted and then re-imported (paired) for the app to work properly again.

Sorry for the circumstances but unfortunately there is no other way…

Gruss Chris

See: [App][Pro] dingz

Bonsoir,
La dernière mise à jour pose problème.
Obligé de remettre tout mes dingz et de refaire mes flow.
Et les boutons ne sont plus détecté par l’application. (Un sur deux voir aucun)

Ceux-ci était détecté avant.

Merci d’avance

Please in English so that everyone understands…

I had announced a week ago, that today the migration to the new version takes place and that you have to import all devices new.

New is that only the buttons that are not assigned to an “output” are displayed. Because I had the problem (and sleepless nights, plus spiteful mails) that if the one who reacts first (Flow or Device) lost and the winner overwrote the loser the settings, so a pure timing problem that I could not influence. So delete via WebUI the outputs of the respective button and this is displayed in the flow…

Please excuse me. I understand your explanation. But there must be a problem. I have a Dingz without any output (All in reserve). When creating a flow, No button is available. I have this problem on several Dingz. Should we also remove them from the Dingz app?

Yep, Reinstall all, because internally everything has changed !!

Hello,

I have a Dingz 4 button switch.
I use two of the buttons the trigger an action on Homey.
Unfortunately since yesterday, it is not working anymore. Maybe a firmware update.

Is there a way to log all the requests received by Homey? I would like to check what is sent from the Dingz.

Thank you in advance.

Chris

Hi Chris thank you for your Great work! But i have a Problem with the Dingz App in Homey. I dont use beta!
Afther the Updates its Not longer possible in the funktion „afther press a buttom“ choice a buttom. Then i follow your Instruktion, clear all entris in the normal dingz App and clear in Homey! It changes nothing. Then i completli dingz to default settings. De- reinstalled the app in homey. But all aktions change nothing. I cant select a buttom! What do i wrong?