[APP][Pro&Cloud] Shelly

I would also need Support for the New Motion 2. I can’t add this Device.

Thx

On what version of the app? Should be supported just fine on 3.9.12.

Will be fixed in the upcoming 3.10.2 release.

Adding the motion 2 will be fixed in release 3.10.2. I have no issues adding two Plus HT myself (a test and a production unit). Could you try pairing it on 3.10.1 and send me a diagnostic report afterwards.

Could you try pairing it on 3.10.1 and send a diagnostic report afterwards. I dont know why the right device config isnt found and I do not have this device to test with.

Adding plus H&T in 3.10.1 works if it is battery powered. When USB powered it goes out of setup mode after a few seconds. I have reported that to Shelly.

1 Like

ah ok. i thought i am too stupid to add the device :slight_smile: . all other shelly devices works fine out of the box. Do you have an eta when the new version will be available? :slight_smile:

v3.10.7 - 10-08-2022

  • Important message: this release contains some non-breaking but fundamental changes. All previous device drivers have been deprecated for both Homey Pro and Homey Cloud. They have been replaced by a single unified driver for all Shelly devices. Your already paired devices will continu to function but new devices should be paired with this new driver. This will make adding future devices to the ever growing collection of Shelly devices a lot easier.

  • Added support for the Shelly Plus HT and Shelly Motion 2 for Homey Pro & Homey Cloud

  • Added support for outbound websockets, a new way of communication for Shelly Plus/Pro devices with Homey Pro

  • Add total energy consumption for Shelly 3EM for Homey Pro and Cloud

  • Add total power consumption for Shelly RGBW2 for Homey Pro and Cloud

  • Fix for Shelly TRV target temperature being out of bounds and causing an app crash

  • Various minor code improvements for both Homey Pro and Cloud

I’m sure the deprecation of currently used device drivers will raise concerns, especially since user will see a message about this in the Homey app. No worries, your devices will continu to function normally within Homey until I decide to fully remove the driver. For a lot of long lived drivers I will probably not remove them at all and no action is required, just ignore the message. I do intend to remove the more recently added drivers for all Plus/Pro devices at some point to reduce the apps footprint. With over 75+ drivers the Shelly app has grown huge. It’s hard to maintain and I’m worried this is starting to impact performance. If you have paired any Plus/Pro devices with Homey you are now encouraged to re-pair them using the new driver. I will probably remove the current drivers after the summer to give users some time to fix their flows.

2 Likes

Trying to add Motion 2 with 3.10.2 throws this error
image

Make sure it’s woken up during pairing. The error tells you Homey cant reach the device.

As far as I can tell, it is awake, responds to web gui, reports motion and tamper.

Must be something in your network or Homey’s network stack be unstable then. The error is quite clear, Homey cant reach IP address 192.168.2.199.

I enabled cloud and added it to the Shelly app and after that is was found by Homey :slight_smile:

1 Like

Version 3.10.1 has stopped responding and the device is not working properly.
v 3.10.2 test works, but sees only one channel for shelly 2.5; (

Please help.

Homey Pro or Homey Cloud? And what does “stopped working” mean? If it works on 3.10.2 it will work on 3.10.1 as well as there are only small unrelated changes.

Homey Cloud Shelly is temporarily unavailable, it will be back shortly. w 3.10.1

That’s about as useful a comment as it is useful to downrate the app in the app store hoping that will resolve your issue. Did you actually rate it 5-stars after it was working correctly for you for months or do you only give bad ratings?

If you really want this resolved I need more info. I guess you are on Homey cloud. Could you post a screenshot of the error and a diagnostic report.

1 Like

If I manage to install the application correctly, and it will detect 2 channels for shelly 2.5, I will give it a 5 rating and write a very positive comment.

Wow lucky me.

1 Like

I installed a test version, but it does not detect both channels for shelly 2.5 I can only control one ae63c7bb-fae6-45a8-9bd4-3657e7dd3e94

Try the new version in the test channel (v3.10.3).