# Fibaro Smoke Detector - Alarm stays on

**URL:** <https://community.homey.app/t/fibaro-smoke-detector-alarm-stays-on/56774>\
**Category:** Devices\
**Created:** [December 17, 2021, 8:55pm UTC](https://community.homey.app/t/fibaro-smoke-detector-alarm-stays-on/56774 "2021-12-17T20:55:50Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Rowel](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/rowel/32/47723_2.png) [@Rowel](https://community.homey.app/u/Rowel)\
**Post date:** [December 17, 2021, 8:55pm UTC](https://community.homey.app/t/fibaro-smoke-detector-alarm-stays-on/56774/1 "2021-12-17T20:55:50Z")

</div>

I recently ran tested one of my Fibaro Smoke Detectors to test a new flow attached to it. All worked fine.

However now in Homey the detector remains in an alarm state. Dash shows the fire icon in red.

Is there a way to reset the smoke detector/alarm mode?

---

<div class="post-metadata">

**Author:** ![DirkG](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/dirkg/32/118897_2.png) [@DirkG](https://community.homey.app/u/DirkG)\
**Post date:** [December 19, 2021, 7:47am UTC](https://community.homey.app/t/fibaro-smoke-detector-alarm-stays-on/56774/2 "2021-12-19T07:47:09Z")

</div>

Maybe this info helps:

> [@Fibaro Smoke Sensor, won´t remove Smoke alarm trigger](https://community.homey.app/t/fibaro-smoke-sensor-won-t-remove-smoke-alarm-trigger/16611/9):
>
> First of all, the Fibaro’s should reset automatically, but if you remove the battery so silence the noise this will probably not happen. I cannot test this as I have no alarm, but the solution should be to activate the green menu item from the Fibaro smoke detector. This menu item will send the current status to Homey, so should reset the alarm. Last but not least, what you could try (and should probably do anyway after smoke detection) is the self test. If taking out the battery was wat cause…

---

<div class="post-metadata">

**Author:** ![Edwin\_D](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/edwin_d/32/136417_2.png) [@Edwin\_D](https://community.homey.app/u/Edwin_D)\
**Post date:** [December 19, 2021, 9:58am UTC](https://community.homey.app/t/fibaro-smoke-detector-alarm-stays-on/56774/3 "2021-12-19T09:58:45Z")

</div>

In the past a Fibaro Smoke alarm test would not trigger a Homey alarm (which is silly to me, but still). This recently changed, so it could be the Homey app was not tested for this situation. I would therefore also put in a ticket at the developer (Athom itself in this case).

---

<div class="post-metadata">

**Author:** ![Rowel](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/rowel/32/47723_2.png) [@Rowel](https://community.homey.app/u/Rowel)\
**Post date:** [January 9, 2022, 11:51am UTC](https://community.homey.app/t/fibaro-smoke-detector-alarm-stays-on/56774/4 "2022-01-09T11:51:11Z")

</div>

Didn’t have a lot of time to test.

Tried all suggestions but the only thing that helped was firing up the test alarm by long holding the button on the sensor again and waiting until it went off and sent the reset signal to Homey.

Thanks!