# Fibaro HC not keeping the set temperature
**URL:** https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029
**Category:** Devices
**Tags:** z-wave
**Created:** [August 18, 2019, 2:55pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029 "2019-08-18T14:55:52Z")
**Posts on this page:** 8
**Page:** 1
### Author:  [@Mlynnerup](https://community.homey.app/u/Mlynnerup)
#### Post date: [August 18, 2019, 2:55pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/1 "2019-08-18T14:55:52Z")
I have two Fibaro Heat Controllers (Z-wave) installed and connected to Homey. No matter how seem to set the temperature, manually or by using a heat controller app, the controllers jump back to 20,5 C a couple of minutes after being set.
Does any else experience this? And how do I avoid it?
It’s almost as if there is some kind of build in schedule in the controller that bypass Homey’s settings.
Any input? Thanks!
---
### Author:  [@Osorkon](https://community.homey.app/u/Osorkon)
#### Post date: [August 18, 2019, 2:57pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/2 "2019-08-18T14:57:40Z")
A range problem can you exclude?
---
### Author:  [@Mlynnerup](https://community.homey.app/u/Mlynnerup)
#### Post date: [August 18, 2019, 3:03pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/3 "2019-08-18T15:03:57Z")
One of the controllers is placed less than 1 meter away from Homey, so I wouldn’t think so…
---
### Author:  [@Osorkon](https://community.homey.app/u/Osorkon)
#### Post date: [August 18, 2019, 3:30pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/4 "2019-08-18T15:30:10Z")
Which Thermostat mode is set?
The Thermostat calibration is also done?
---
### Author:  [@Mlynnerup](https://community.homey.app/u/Mlynnerup)
#### Post date: [August 18, 2019, 3:39pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/5 "2019-08-18T15:39:02Z")
I can try the calibration. Where do I set the mode?
---
### Author:  [@Osorkon](https://community.homey.app/u/Osorkon)
#### Post date: [August 18, 2019, 3:45pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/6 "2019-08-18T15:45:30Z")
I don’t own a Fibaro Heat Controller.
But you should be able to set the mode in the device settings, like for a Spirit Thermostat.
---
### Author:  [@Mlynnerup](https://community.homey.app/u/Mlynnerup)
#### Post date: [August 18, 2019, 3:54pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/7 "2019-08-18T15:54:03Z")
Calibration didn’t make a difference, unfortunately.
I don’t have the possibility to select a mode. I just set the temperature directly.
---
### Author:  [@Mlynnerup](https://community.homey.app/u/Mlynnerup)
#### Post date: [August 18, 2019, 4:33pm UTC](https://community.homey.app/t/fibaro-hc-not-keeping-the-set-temperature/17029/8 "2019-08-18T16:33:34Z")
Actually, I might have found the solution.
I was stupid enough to only test the setup using very low temperatures. It looks like the Fibaro controller doesn’t accept temperatures below 10 C. After I started testing higher temperatures, it seems to be working 😒
Thanks for your input though!