# Connect Fibaro implant to garage door

**URL:** <https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446>\
**Category:** Devices\
**Created:** [June 28, 2023, 2:26pm UTC](https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446 "2023-06-28T14:26:45Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![perage](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/perage/32/72711_2.png) [@perage](https://community.homey.app/u/perage)\
**Post date:** [June 28, 2023, 2:26pm UTC](https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446/1 "2023-06-28T14:26:45Z")

</div>

Hi,

I have a simple garage door with just two outputs going into a simple button. Pressing it opens/closes the gate.

Which input/output should be used on the implant? I hope it will be powered by the same two cables as the buttons are:)

---

<div class="post-metadata">

**Author:** ![robertklep](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/robertklep/32/160628_2.png) [@robertklep](https://community.homey.app/u/robertklep)\
**Post date:** [June 28, 2023, 2:49pm UTC](https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446/2 "2023-06-28T14:49:44Z")

</div>

From what I can see, the button is connected to GND and IN1 (or IN2, I don’t think it matters). Then, the existing wires that go to the button are connected to OUT1 (or OUT2 if you’re using IN2). Since apparently your system works with a pulse input (pressing a button) you may have to configure the implant to do the same with its output (so it pulses OUT1/OUT2 when you press the button or turn the device on/off remotely).

The implant will not be powered by those wires because they are switching wires, not power wires.

---

<div class="post-metadata">

**Author:** ![DirkG](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/dirkg/32/118897_2.png) [@DirkG](https://community.homey.app/u/DirkG)\
**Post date:** [June 28, 2023, 5:52pm UTC](https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446/3 "2023-06-28T17:52:15Z")

</div>

> [@perage](#):
>
> I hope it will be powered by the same two cables as the buttons are:)

Hope is not a good advisor in electrical things.

 ![IMG_3660](https://us1.discourse-cdn.com/flex025/uploads/athom/original/3X/1/0/1006e8c1a690d51edd433cf464750ebbf2df1c39.jpeg)

---

<div class="post-metadata">

**Author:** ![perage](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/perage/32/72711_2.png) [@perage](https://community.homey.app/u/perage)\
**Post date:** [June 28, 2023, 6:26pm UTC](https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446/4 "2023-06-28T18:26:01Z")

</div>

Haha, true! But One cable for 9v - should be two right? I see the drawing puts the implant between the opener and the button but it should be possible to just put it side-by-side as well right?

---

<div class="post-metadata">

**Author:** ![DirkG](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/dirkg/32/118897_2.png) [@DirkG](https://community.homey.app/u/DirkG)\
**Post date:** [June 28, 2023, 6:55pm UTC](https://community.homey.app/t/connect-fibaro-implant-to-garage-door/83446/5 "2023-06-28T18:55:12Z")

</div>

There are two cables for power supply:  
9-30 V resp. P = + cable/connection  
GND = - cable/connection

 ![IMG_3661](https://us1.discourse-cdn.com/flex025/uploads/athom/original/3X/5/c/5cec8b077187f06165f5384b9854cf8e07dfccd6.jpeg)

If the SI can be powered by the clamps where the button is connected, you have to check if the DC voltage is between 9-30 V.