# \[APP\]\[Pro\] Enphase Controller **URL:** \ **Category:** Apps\ **Tags:** app, homey-pro\ **Created:** [June 3, 2026, 6:59pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720 "2026-06-03T18:59:31Z")\ **Posts on this page:** 20\ **Page:** 7
**Author:** ![Joep\_Vullings](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/joep_vullings/32/9293_2.png) [@Joep\_Vullings](https://community.homey.app/u/Joep_Vullings)\ **Post date:** [September 10, 2026, 10:40am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/122 "2026-09-10T10:40:56Z")
Yes, they have been installed in the app, see below. The ‘besturingstoegang’ hasn’t been updated since 2 months. The Gateway has been updated yesterday though. ![Schermafbeelding 2026-09-10 om 12.39.15](https://us1.discourse-cdn.com/flex025/uploads/athom/original/3X/5/f/5fe9ff9a14c79da0ae3e58c2d298369f2a83919b.png) ---
**Author:** ![Joep\_Vullings](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/joep_vullings/32/9293_2.png) [@Joep\_Vullings](https://community.homey.app/u/Joep_Vullings)\ **Post date:** [September 10, 2026, 5:22pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/123 "2026-09-10T17:22:56Z")
Deleting device and re-pairing didn’t work. ---
**Author:** ![Joep\_Vullings](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/joep_vullings/32/9293_2.png) [@Joep\_Vullings](https://community.homey.app/u/Joep_Vullings)\ **Post date:** [September 28, 2026, 12:08pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/124 "2026-09-28T12:08:18Z")
So, I had Enphase enabling my Modbus, but still it says ‘Nee’ at ‘besturingstoegang’. Any clues? ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [September 28, 2026, 3:00pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/125 "2026-09-28T15:00:11Z")
Controller access (“Besturingstoegang”) is solely dependent on the account-type that’s being used. Modbus/CT-clamps are not a factor. A normal “owner” account will not give you controller access. You need an Installer or Maintainer account. Please refer to the startpost of this thread and read the stuff under “**Instructions for getting Maintainer (Control) access to your Enphase system**”. If you already did that, and if you’re absolutely sure you’re authenticating in the app with an Installer or Maintainer account, send me an App Diagnostic **after (re)trying the login** with the correct account credentials. Put “account not recognized as installer/maintainer” in the description please. ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [September 28, 2026, 3:05pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/126 "2026-09-28T15:05:20Z")
_For others monitoring this thread:_ I’m currently working on a 2.0 release with **support for the Enphase Battery** (thanks to [work](https://community.homey.app/t/app-enphase-harness-the-sun-to-make-use-save-and-sell-your-own-power/134602/104) done by @Niels ). Test versions for this release will come soon (1.9.x). Heads up: in this release I’ll be refactoring a bunch of device drivers to make the internal structure off the app better for including more Enphase products. In 2.0 most existing devices will therefore become deprecated (but will still work). ---
**Author:** ![iNoch](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/inoch/32/30349_2.png) [@iNoch](https://community.homey.app/u/iNoch)\ **Post date:** [October 2, 2026, 9:13pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/127 "2026-10-02T21:13:47Z")
> [@bramtops](#): > > 1. After granting access, right below that you’ll find a “ **PV system maintainer** ” pull down. Select **your fake company** there. 1. After granting access, right below that you’ll find a “ **PV system maintainer** ” pull down. Select **your fake company** there. Unfortunately, no pull down menu to be found. Maybe my installer has blocked this option? Any workaround? ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 6, 2026, 4:35pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/128 "2026-10-06T16:35:28Z")
Thats a new one for me; you’re the first to report no PV system maintainer. I’ve look at my “Access control” page to be sure, and the pulldown is still there for me. Does that page list 2 companies under “Companies”. Its should mention your original installer plus your own fake company. ---
**Author:** ![Franck\_VITKOVSKY](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/franck_vitkovsky/32/120754_2.png) [@Franck\_VITKOVSKY](https://community.homey.app/u/Franck_VITKOVSKY)\ **Post date:** [October 9, 2026, 7:26am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/129 "2026-10-09T07:26:37Z")
Hi Bram, metered IQ Gateway (fw D8.3.5169) apparently without production CT clamps, app 1.5.2, owner account. Even after deleting and re-adding “Enphase Solar” today, Metered gateway = Yes, power stays 0.5–3 W day and night and energy today = 0 kWh, while the inverters device shows ~150 W total at the same time (utility meter: 5.38 kWh yesterday). Diagnostic report: de76598c-90d9-4420-8d19-c1b265265390. Could the app fall back to the inverters sum when no production CT is active? Thanks! ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 9, 2026, 11:56pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/130 "2026-10-09T23:56:17Z")
Thanks for the report. I’m looking into what’s happening here and I’ll see if I can include a patch in the upcoming 2.0. ---
**Author:** ![iNoch](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/inoch/32/30349_2.png) [@iNoch](https://community.homey.app/u/iNoch)\ **Post date:** [October 10, 2026, 9:06pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/131 "2026-10-10T21:06:33Z")
sorry, my mistake. I misread “Een ander bedrijf toegang verlenen door het e-mailadres op te geven van een Enlighten-gebruiker uit dat bedrijf.” as add email address from the existing company only. Just added my fake company now and installation went smoothly. Will play around now.. ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 12, 2026, 8:21pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/133 "2026-10-12T20:21:14Z")
Hi, and thanks for the report. It looks like your gateway is reporting that it does have CT clamps, but they are not connected, so the app only reads the “noise” (0.5-3 W). I’ve added an option “Ignore production meters” to the Solar device settings. During pairing, the app will detect both values, and if a large enough discrepancy is detected, it will turn this setting on for you. If you pair during the night, the app obviously can’t see this discrepancy and you’ll need to enable the setting manually. This will be added in the upcoming 2.0 release (which is imminent). ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 12, 2026, 8:44pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/134 "2026-10-12T20:44:20Z")
# [Version 2.0 test](https://homey.app/en-nl/app/nl.creitive.enlighten/Enphase-Controller/test/) is out now. Changelog: - This release reworks several internal systems for more reliability and future updates. Unfortunately some devices will have to be re-added. - Adds Enphase battery monitoring. - Adds animated energy flow widget (only for metered systems). - Homey alarm support for inverter problems. - Adds deprecation notices to timeline for older drivers. - Adds French and German language support. - Support for unwired production meters. Battery support and the widget are copied and adapted from [here](https://community.homey.app/t/app-enphase-harness-the-sun-to-make-use-save-and-sell-your-own-power/134602/104), thanks @Niels! ---
**Author:** ![SpikeHome](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/spikehome/32/9435_2.png) [@SpikeHome](https://community.homey.app/u/SpikeHome)\ **Post date:** [October 14, 2026, 9:56am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/135 "2026-10-14T09:56:30Z")
installed it, not have to reinstall devices. Added Battery now and added widget. ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 14, 2026, 10:55am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/136 "2026-10-14T10:55:03Z")
Thanks, let me know how it works for you! FYI, the existing devices will still work _for now_. But you’ll get a warning message on your timeline when installing 2.0, and those devices _will stop working_ in a future version. ---
**Author:** ![GPaz](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/gpaz/32/3631_2.png) [@GPaz](https://community.homey.app/u/GPaz)\ **Post date:** [October 18, 2026, 8:23pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/137 "2026-10-18T20:23:39Z")
Hi bramtops I installed your excellent app a few days ago and have encountered what I think is strange behavior in the reporting of the “Solar energy today” data for my Enphase Solar device. I assume this datapoint is to report on the total solar energy generated in a day and is reset at end/start of each day. Unfortunately for me, the value appears to be zeroing out at 11am each day, resulting in inaccurate reporting on the amount of solar generated. The bottom of each curve in the graph below is at 11am each day ![IMG_0447](https://us1.discourse-cdn.com/flex025/uploads/athom/original/3X/8/3/839276d599c4f9bdc3be9229d2de98f9026b5a66.jpeg) I am on the east coast of Australia and 11am is 00:00UTC, so am assuming there maybe a timezone issue in the app. Would you please either advise if there is an issue, or if I am misreading the purpose of this datapoint. Many thanks. ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 19, 2026, 7:59am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/138 "2026-10-19T07:59:13Z")
Thats very likely a timezone issue and should be an easy fix. Is this on [1.5](https://homey.app/en-us/app/nl.creitive.enlighten/Enphase-Controller/) or [2.0](https://homey.app/en-us/app/nl.creitive.enlighten/Enphase-Controller/test/)? ---
**Author:** ![GPaz](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/gpaz/32/3631_2.png) [@GPaz](https://community.homey.app/u/GPaz)\ **Post date:** [October 19, 2026, 8:47am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/139 "2026-10-19T08:47:48Z")
Thanks and apologies for not providing the app version in my earlier post. It’s 2.0.0. Regards ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 19, 2026, 8:59am UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/140 "2026-10-19T08:59:44Z")
No problem! I’ll take a look and have it fixed in the next test-release. ---
**Author:** ![bramtops](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bramtops/32/166144_2.png) [@bramtops](https://community.homey.app/u/bramtops)\ **Post date:** [October 19, 2026, 9:40pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/141 "2026-10-19T21:40:43Z")
2.0.1 just released on the [test branch](https://homey.app/en-nl/app/nl.creitive.enlighten/Enphase-Controller/test/). It should be fixed now. ---
**Author:** ![GPaz](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/gpaz/32/3631_2.png) [@GPaz](https://community.homey.app/u/GPaz)\ **Post date:** [October 19, 2026, 10:26pm UTC](https://community.homey.app/t/app-pro-enphase-controller/155720/142 "2026-10-19T22:26:17Z")
Thanks. I have just installed your new test version. Solar totals have been set to zero (which I assume is expected as device has been updated) and incrementing by current power generation. iWill check at 11am this morning and let you know. [Previous page](https://community.homey.app/t/app-pro-enphase-controller/155720.md?page=6) [Next page](https://community.homey.app/t/app-pro-enphase-controller/155720.md?page=8)