# \[APP\]\[Pro\] Creality - Control your Creality 3D printers
**URL:** https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419
**Category:** Apps
**Tags:** app, homey-pro, community-app
**Created:** [February 1, 2026, 1:19pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419 "2026-02-01T13:19:38Z")
**Posts on this page:** 20
**Page:** 3
### Author:  [@Nelson1976](https://community.homey.app/u/Nelson1976)
#### Post date: [April 28, 2026, 2:31pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/41 "2026-04-28T14:31:00Z")
ben ik weer, wanneer ik een flow wil maken en start met creality zie ik alleen de temp kaarten ik heb geen runout kaart gezien, heb ik iets fout gedaan of moet ik de app opnieuw downloaden en installeren? wederom bedankt voor al jou moeite
---
### Author:  [@Nelson1976](https://community.homey.app/u/Nelson1976)
#### Post date: [April 30, 2026, 1:31pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/42 "2026-04-30T13:31:12Z")
hallo ik heb weer een kleine bug gevonden, het ophalen van gegevens gaat niet helemaal gelijk het verschil is gigantisch, zie de afbeeldingen op zelfde moment foto’s genomen
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [May 10, 2026, 11:11am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/43 "2026-05-10T11:11:25Z")
Big thanks to the developer for adding the Creality Hi and Hi Combo. Widget, flows and device pages work really well.
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [June 6, 2026, 6:44pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/44 "2026-06-06T18:44:22Z")
Change Log v1.1.15
Added support for Homey camera video streams on K1 Max, Hi, and Hi Combo devices.
The camera stream has been configured to reconnect when the printer’s IP address is changed.
The camera feed currently works only on the local network. Live video is not supported because Homey cannot convert the MJPEG stream via a WebRTC proxy for external network or remote access.
The issue where the print preview image in the Status widget would briefly disappear and reappear has been fixed.
A safety check has been added to the K1 Max, Hi, Hi Combo, and Generic Klipper control commands to display a clearer error message when the connection is not ready.
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 2, 2026, 7:33pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/45 "2026-07-02T19:33:16Z")
Change Log v1.1.17
Reliability fixes:\*\* commands (pause/resume/stop/light/home) sent while the printer is unreachable now correctly report failure instead of appearing to succeed. Status polling now closes the connection as soon as data is received, restoring the intended fast on-demand polling behavior instead of holding sockets open for up to 4 seconds. Fixed a bug where finishing a print successfully could incorrectly fire the “Print stopped” flow trigger. Devices now properly stop polling and release camera resources when removed from Homey. Hardened the Status widget’s image proxy against being used to fetch arbitrary internal network addresses. Fixed the “press stop again to confirm” message disappearing instantly on Klipper/K1 Max devices.
> **[Creality | Homey](https://homey.app/en-tr/app/com.creality/Creality/)**
>
> Control your Creality 3D printers
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 8, 2026, 5:53pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/46 "2026-07-08T17:53:42Z")
Change Log v1.2.2 Test
Temperature control: read and set nozzle and bed target temperatures from the device or Flows. Layer tracking: new Current Layer and Total Layers sensors, shown in the Status widget, with a “Current layer is at least” Flow condition. Speed & flow control: new Print Speed and Flow Rate sensors plus Flow actions to adjust them (M220/M221). Fan control: new Flow action to set part cooling, case, and side fan speeds. Error reporting: new “Print error occurred” Flow trigger with the error message as a token. Hi Combo CFS: new Active Filament sensor showing the slot, material, and remaining percentage in use; slot overview now includes material, color, and remaining percentage per slot; fixed CFS values flickering to zero between updates. New CFS Filament dashboard widget with per-slot filament color rings, remaining percentage, active slot indicator, external spool row, and box temperature/humidity. Discovery: printers are now discovered automatically via mDNS during pairing (manual IP entry is still available). Connectivity: polling now backs off gradually up to 60 seconds while the printer is unreachable and recovers instantly. The K1 Max driver is now labeled K1 / Ender V3 Series, as all K1 and Ender V3 family printers running stock Creality firmware use the same protocol.
> **[Creality | Homey](https://homey.app/en-tr/app/com.creality/Creality/test/)**
>
> Control your Creality 3D printers
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 7:21am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/47 "2026-07-15T07:21:28Z")
Running version 1.2.2. With A Creality Hi CFS Combo.
Should the camera be working in the device page?
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 15, 2026, 7:32am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/48 "2026-07-15T07:32:03Z")
Yes, the camera feed should be visible. If you send me the diagnostic log, I can figure out where the error is.
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 7:52am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/49 "2026-07-15T07:52:11Z")
Thanks. Log sent #580d9edf-15b4-43e1-8dcb-6cc26a82fe7c
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 15, 2026, 8:47am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/50 "2026-07-15T08:47:59Z")
> [@philthynz](#):
>
> Running version 1.2.2. With A Creality Hi CFS Combo.
>
> Should the camera be working in the device page?
Yes, the camera is supported on the Hi Combo device page, but only for local network viewing. In this case the logs show Homey cannot reach the printer at 192.168.1.230, so please verify the printer IP/network connection and test [http://192.168.1.230:8080/?action=stream](http://192.168.1.230:8080/?action=stream) from the same local network.
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 9:13am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/51 "2026-07-15T09:13:13Z")
Hi, the camera stream is on [http://192.168.1.230:8000/](http://192.168.1.230:8000/) not port 8080.
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 15, 2026, 9:34am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/52 "2026-07-15T09:34:54Z")
Test v1.2.3
- Fixed camera streaming for Creality Hi and Hi Combo printers by using the correct `http://PRINTER_IP:8000/` stream address.
- K1 Max camera streaming continues to use port `8080`.
- Camera feeds are available only on the local network; remote viewing through Homey Cloud is not supported.
[https://homey.app/en-tr/app/com.creality/Creality/test/](https://homey.app/en-tr/app/com.creality/Creality/test/)
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 10:13am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/53 "2026-07-15T10:13:26Z")
Tried to reinstall and re-add the Creality Hi. Still no video. Diagnostic log #89758bbb-30b4-4bff-bec9-e592123d5331
Many thanks for your time. I’ve attached a screenshot showing port 8000 working in Chrome but no video in Homey app.
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 15, 2026, 10:16am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/54 "2026-07-15T10:16:49Z")
The log shows this is not yet a camera-stream error. The device has no valid printer IP:
Invalid printer IP address
In the Homey device settings, enter:
IP Address: 192.168.1.230
Port: 9999
Do not enter [http://192.168.1.230:8000/](http://192.168.1.230:8000/) in the IP field. The app automatically uses port 8000 for the Hi/Hi Combo camera.
After saving the settings, restart the app or re-add the device if the IP remains empty. Camera viewing is available only on the same local network.
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 10:32am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/55 "2026-07-15T10:32:50Z")
Yes that is how I have added the device. IP and Port only. See screenshot.
And I have restarted the app and re-added the device.
Diagnostic log #e78f0d60-8cd8-4a85-b07f-274b9dc67f17
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 10:34am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/56 "2026-07-15T10:34:42Z")
And yes Homey does have connectivity. I can curl the video stream from Homey server.
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 15, 2026, 10:46am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/57 "2026-07-15T10:46:41Z")
Could you test it and report the result again?
[https://homey.app/en-tr/app/com.creality/Creality/test/](https://homey.app/en-tr/app/com.creality/Creality/test/)
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 15, 2026, 11:00am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/58 "2026-07-15T11:00:32Z")
Error here
---
### Author:  [@ugrbnk](https://community.homey.app/u/ugrbnk)
#### Post date: [July 15, 2026, 1:12pm UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/59 "2026-07-15T13:12:50Z")
After launching the application, open the camera screen, wait 10-15 seconds, and capture the log generated during that time
[https://homey.app/en-tr/app/com.creality/Creality/test/](https://homey.app/en-tr/app/com.creality/Creality/test/)
---
### Author:  [@philthynz](https://community.homey.app/u/philthynz)
#### Post date: [July 16, 2026, 9:52am UTC](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419/60 "2026-07-16T09:52:48Z")
Thanks. Log #c0cf0613-6d47-4c18-a237-1edb5322d11b
[Previous page](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419.md?page=2)
[Next page](https://community.homey.app/t/app-pro-creality-control-your-creality-3d-printers/150419.md?page=4)