# \[APP\] Aqara & Xiaomi Smart Home - Simplify your life with a smarter home **URL:** \ **Category:** Apps\ **Tags:** app, zigbee\ **Created:** [August 22, 2018, 8:18pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156 "2018-08-22T20:18:09Z")\ **Posts on this page:** 20\ **Page:** 355
**Author:** ![Drako74](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/drako74/32/150506_2.png) [@Drako74](https://community.homey.app/u/Drako74)\ **Post date:** [October 13, 2026, 7:41pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7402 "2026-10-13T19:41:55Z")
This sounds like the update we’ve all been waiting for… nicely done good sir 🫡 Muchly appreciated ---
**Author:** ![Bo\_Alvhage](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/bo_alvhage/32/178957_2.png) [@Bo\_Alvhage](https://community.homey.app/u/Bo_Alvhage)\ **Post date:** [October 14, 2026, 1:24pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7403 "2026-10-14T13:24:18Z")
Hi @TedTolboom, I’m having problems with the Aqara Temperature and Humidity Sensor T1 (lumi.sensor\_ht.agl02) on my Homey Pro 2019. Homey firmware: 13.5.1 Aqara app: 1.18.1 I’ve tested two brand-new T1 sensors from the same 3-pack. Both pair successfully and appear correctly in the Zigbee network, but neither reports temperature, humidity or pressure values. I’ve tried re-pairing close to Homey (1 metre), keeping the sensors awake during pairing, and restarting the Aqara app. My older Aqara temperature sensors (lumi.weather) have worked reliably for years. **Diagnostic report ID:** cdbf16d6-fb7d-4c73-abf9-252cddf88ff1 Is this a known compatibility issue with Homey Pro 2019? Is there a solution without replacing the hub or sensors? Thanks for your help! ---
**Author:** ![Alex7](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/alex7/32/120885_2.png) [@Alex7](https://community.homey.app/u/Alex7)\ **Post date:** [October 14, 2026, 8:44pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7404 "2026-10-14T20:44:50Z")
Hello, I am having issues pairing my Aqara Wireless Mini Switch to Homey. I have connected this button in the past but did a reset on the Homey last year and am just now getting around to re adding. Diagnostic Code: 8ef550d8-0907-42b7-bece-36947068ca2d I have gone through all known troubleshooting steps and can not get this to connect. Here are the steps I took: restarted homey, removed and re installed aqara app on homey, tried to pair under 2018 and standard model, tried to pair via sole zigbee pairing. None of these have worked. Is there a trick to getting these to pair? ---
**Author:** ![Hass](https://avatars.discourse-cdn.com/v4/letter/h/51bf81/32.png) [@Hass](https://community.homey.app/u/Hass)\ **Post date:** [October 15, 2026, 5:12pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7405 "2026-10-15T17:12:36Z")
Hello. Thank you for adding W100 support. I’m trying to create a flow for one of my W100 devices (Zigbee) using the buttons, but it gives an error message simply adding the card. It also says “Chose button”, but the list is empty. ![image](https://us1.discourse-cdn.com/flex025/uploads/athom/original/3X/f/b/fbfad5ab27e61bf651f101acd2cb3742ad54df83.png) If I try creating the flow from the iOS app using the same trigger card, both dropdown lists are empty. Diagnostic ID: f49c37db-a7ff-45cc-9322-7ab7c34b4ce2 ---
**Author:** ![TedTolboom](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/tedtolboom/32/12081_2.png) [@TedTolboom](https://community.homey.app/u/TedTolboom)\ **Post date:** [October 15, 2026, 7:23pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7406 "2026-10-15T19:23:44Z")
I just released v1.19.1 to the [app store test environment](https://homey.app/a/com.xiaomi-mi/test/). @Alex7 @Hass this should address your issues. Changelog: **## Aqara v1.19.1** > Requires **\*\*Homey v13.1.0\*\*** or newer. * * * ### ⚠ Battery alarm replaced by battery level To align with app store guidelines battery powered devices now only show the **battery level** (%), no longer a battery alarm. - **Flows using the battery alarm** of these devices stop working and need to be updated (e.g. to _The battery level dropped below …_). - \*_Smoke detectors\*_ keep their battery alarm. * * * ### Fixes and improvements - **Temperature and humidity sensor T1:** improving robustness of reporting after pairing. Existing sensors recover by themselves, no re-pairing needed (pressing the button will accelerate). - **TVOC air quality monitor:** more reliable reporting, a stable battery level and a new **display unit** setting (press the sensor’s button after saving). - **Climate sensor W100:** the _\*button pressed\*_ flow card works again. - **Vibration sensor T1:** added the _vibration alarm turned on / off_ flow cards. - **Various fixes** for the Dimmer switch H2, smoke detector, wall switches, relay controller and Smart plug EU. ---
**Author:** ![Paul\_Nas](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/paul_nas/32/80581_2.png) [@Paul\_Nas](https://community.homey.app/u/Paul_Nas)\ **Post date:** [October 16, 2026, 10:24am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7407 "2026-10-16T10:24:18Z")
Hi @TedTolboom, any chance of adding the E1 double remote? I have both the single and double remotes and the single remote is recognised (lumi.remote.acn003) but the double (lumi.remote.acn004) is not. Thanks! ---
**Author:** ![TedTolboom](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/tedtolboom/32/12081_2.png) [@TedTolboom](https://community.homey.app/u/TedTolboom)\ **Post date:** [October 16, 2026, 11:16am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7408 "2026-10-16T11:16:08Z")
lumi.remote.acn004 should be recognized properly. Can you check / confirm if the manufacturerName is reported as Aqara instead of LUMI (hence it is not recognized properly)? ---
**Author:** ![Paul\_Nas](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/paul_nas/32/80581_2.png) [@Paul\_Nas](https://community.homey.app/u/Paul_Nas)\ **Post date:** [October 16, 2026, 11:35am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7409 "2026-10-16T11:35:34Z")
It reports as LUMI, not Aqara. ---
**Author:** ![TedTolboom](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/tedtolboom/32/12081_2.png) [@TedTolboom](https://community.homey.app/u/TedTolboom)\ **Post date:** [October 16, 2026, 12:53pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7410 "2026-10-16T12:53:21Z")
Did you try to include based on the v1.19.1 version in test environment (see link above)? ---
**Author:** ![TedTolboom](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/tedtolboom/32/12081_2.png) [@TedTolboom](https://community.homey.app/u/TedTolboom)\ **Post date:** [October 16, 2026, 1:26pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7411 "2026-10-16T13:26:07Z")
Version v1.19.1 is released to the app store: > [@TedTolboom](#): > > **## Aqara v1.19.1** > > > Requires **\*\*Homey v13.1.0\*\*** or newer. > > * * * > > ### ⚠ Battery alarm replaced by battery level > > To align with app store guidelines battery powered devices now only show the **battery level** (%), no longer a battery alarm. > > - **Flows using the battery alarm** of these devices stop working and need to be updated (e.g. to _The battery level dropped below …_). > - \*_Smoke detectors\*_ keep their battery alarm. > > * * * > > ## New devices > > - **Presence sensor FP1** (RTCZCGQ11LM): presence and a _Presence event detected_ flow card (e.g. enter, leave, approach, away), with settings for sensitivity, monitoring mode and approach distance. Includes a _Reset no presence_ maintenance action. Thanks to @Gabriel_Pedrosa_Mach for your contribution here! > - **Motion sensor E1** (RTCGQ15LM): motion, illuminance and battery. > - **High precision motion sensor** (RTCGQ13LM): motion and battery, with sensitivity and a detection interval setting (2–180 s). > - **Door and window sensor E1** (MCCGQ14LM) > - **Water leak sensor E1** (SJCGQ13LM) > - **Wireless remote switch E1** , single rocker (WXKG16LM) and double rocker (WXKG17LM) > - **Wireless mini switch E1** (WXKG20LM) > - **Wall switch H1 Pro** , triple rocker with neutral (QBKG32LM) > > * * * > > ## Thermostats and climate sensor: external sensor input > > _Applies to: Smart Radiator Thermostat E1, Floor Heating Thermostat W500, Smart Radiator Thermostat W600, Climate sensor W100_ > > - **The last external value is kept alive.** The app re-sends the last temperature (and humidity) set by your flow every 30 minutes, for up to 3 hours. Without a new value within 3 hours, the device falls back to its internal sensor. It switches back to the external sensor automatically with the next value. > - **E1:** the E1 doesn’t fall back by itself (it keeps its last external value), so after 3 hours without a new value the app tells it that the external sensor is offline (falling back to the internal sensor). > > - **The “Temperature sensor” setting stays on “external”** when the thermostat falls back by itself. > - **Requests from the thermostats are answered** with the last value, also after an app restart. > > > 💡 **Tip:** run the _Set the external room temperature_ / _humidity_ flow on every change of your sensor **and** periodically (e.g. every 15 minutes). The flow card hints now explain this. > > * * * > > ## Presence sensors > > - **FP300:** > - Presence and PIR detection are reported reliably, and an alarm that should have reset no longer stays on. > - Added LED indicator setting. > > - **FP1E:** detection range and sensitivity updates. > > * * * > > ## Cube T1 Pro > > - **Operation mode switching works:** the new mode is sent when the cube opens its configuration window. After saving, throw the cube or press its LINK button once. The setting also follows the cube when you switch the mode on the cube itself (LINK button 5 times). > - **A rotation now triggers one _Rotate_ event** with the total angle, instead of several partial ones. > > * * * > > ## Vibration sensors > > - **Vibration sensor (DJT11LM):** > - Tilt angles are corrected. > - The _Set tilt reference_ setting is replaced by a **maintenance action**. > - The relative tilt angle now updates with every tilt event. > > - **Vibration sensor T1:** > - The sensitivity setting is fixed. > - Battery percentage added. > > * * * > > ## Light sensor T1 > > - Darkness now shows as 0 lux instead of 1 lux, and values are rounded to whole lux. > - Each light change is reported once instead of twice. Existing sensors are corrected automatically the next time they report. > - Battery percentage added. > > * * * > > ## Smoke detector and water leak sensors > > - **Smoke detector:** battery percentage added. > - **Water leak sensor T1:** the water alarm is checked against the sensor’s regular status report, so a missed alarm or “dry” message no longer leaves the wrong state in Homey. > > * * * > > ### Fixes and improvements > > - **Temperature and humidity sensor T1:** improving robustness of reporting after pairing. Existing sensors recover by themselves, no re-pairing needed (pressing the button will accelerate). > - **TVOC air quality monitor:** more reliable reporting, a stable battery level and a new **display unit** setting (press the sensor’s button after saving). > - **Climate sensor W100:** the _\*button pressed\*_ flow card works again. > - **Vibration sensor T1:** added the _vibration alarm turned on / off_ flow cards. > - **Various fixes** for the Dimmer switch H2, smoke detector, wall switches, relay controller and Smart plug EU. > > ## All devices > > - **Firmware version in the device settings:** shows the version as in the Aqara app (e.g. `0.0.0_0035`), read from the device. This now also covers older devices such as the door and window sensor, water leak sensor and temperature and humidity sensor. For devices added before this version it is filled in the next time the device reports. > - **Settings on battery powered devices** are no longer lost when the device is asleep. The app writes them the next time the device wakes up, so there is no need to wake the device right before saving. > - **Fewer devices dropping off the network:** > - The app answers the reset request of wall switches, relay modules and several remotes. > > - **Button and scene presses:** > - The waiting time after a press is shorter, so a quick second press is no longer missed. > - The app checks that buttons and remotes stay in the mode that reports button presses ---
**Author:** ![Paul\_Nas](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/paul_nas/32/80581_2.png) [@Paul\_Nas](https://community.homey.app/u/Paul_Nas)\ **Post date:** [October 16, 2026, 6:12pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7412 "2026-10-16T18:12:59Z")
I have installed the test version now. The single rocker WXKG16LM is recognised correctly, very happy with that! The double rocker WXKG17LM however can’t be added, it errors halfway through the setup. It won’t even be added as a generic Zigbee device. Before I installed the test version, it was added as a generic device. ---
**Author:** ![TedTolboom](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/tedtolboom/32/12081_2.png) [@TedTolboom](https://community.homey.app/u/TedTolboom)\ **Post date:** [October 16, 2026, 6:50pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7413 "2026-10-16T18:50:11Z")
> [@Paul\_Nas](#): > > The double rocker WXKG17LM however can’t be added, it errors halfway through the setup. It won’t even be added as a generic Zigbee device. Before I installed the test version, it was added as a generic device. Restart Homey and wait until fully loaded, pull out the battery of the double rocker and drink a coffee (wait for a few minutes) and then install the battery and retry to add the switch. ---
**Author:** ![Trond\_Nordfjaern](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/trond_nordfjaern/32/49124_2.png) [@Trond\_Nordfjaern](https://community.homey.app/u/Trond_Nordfjaern)\ **Post date:** [October 16, 2026, 7:04pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7414 "2026-10-16T19:04:02Z")
@TedTolboom how is the W600 testing going on your side? I got 5 of them the other day and unfortunately have serious issues. Not sure if it is related to the Homey app or if I have hw issues at the radiators. The radiators/valves frequently indicate that they are not heating in Homey, while they are heating at the physical radiator (often they are at or above the setpoint value when this happens read directly on the valve, making me suspect a hw issue). Have tried recalibrations, reseating etc and I am running out of ideas (no adapters involved as they fit directly on the radiators). Sometimes they also indicate heating in homey while no heating happens at the radiator. I am running them at zigbee at the moment, but seems like an Aqara hub is required to change them back to Matter/thread so can not check if that improves things (I could change them over to zigbee from matter/thread without a hub so really strange). These will go back to the vendor and I will return to the semi-semi-reliable Netatmo valves if the sitation does not improve. ---
**Author:** ![TedTolboom](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/tedtolboom/32/12081_2.png) [@TedTolboom](https://community.homey.app/u/TedTolboom)\ **Post date:** [October 16, 2026, 7:40pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7415 "2026-10-16T19:40:07Z")
> [@Trond\_Nordfjaern](#): > > @TedTolboom how is the W600 testing going on your side? I got 5 of them the other day and unfortunately have serious issues. Not sure if it is related to the Homey app or if I have hw issues at the radiators. Did you test based on v1.19.x, as just released today? It does include quite some updates to the W600 thermostat driver. It is still possible to switch back from Zigbee to Matter. You need to remove the device from Homey, open the Aqara (iOS or Android) app and with Bluetooth enabled it should detect the device automatically. It will then show an option to switch between Thread or Zigbee. No Aqara Hub required. ---
**Author:** ![Trond\_Nordfjaern](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/trond_nordfjaern/32/49124_2.png) [@Trond\_Nordfjaern](https://community.homey.app/u/Trond_Nordfjaern)\ **Post date:** [October 16, 2026, 7:49pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7416 "2026-10-16T19:49:59Z")
Thank you. I use 1.19.1 as released today. I did remove the device from Homey and even restarted Homey thereafter to make sure it was gone from the zigbee stack. When trying to add the device in the Aqara Android app it did not detect it automatically and tried to add the device both through matter code and QR. Never reached the mode switch that appared when the device came from the factory. Guess anyway that zigbee vs matter just deals with communication and should not have any effect on temp regulation and operation as such (?) Edit: I may start to see some system in the madness. It seems like these valves systematically close heating when the temp reaches 2 degrees above the actual set point(!), heating sets in when below same thereshold. I have set them to +2 offset and will observe them for a few days more and come back to you, but that is the closest I am to seeing a pattern so far. Valve position tends to move to 0% when around 2 degrees above setpoint. As a sidenote, they also immidently behave like they should after calibration and also turn down heat when set to 5 degrees (off) so that actually reduces the likelihood of the hw hypothesis (valve is clearly able to open and close by radiator pin). Thanks for your patience on this issue. ---
**Author:** ![Trond\_Nordfjaern](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/trond_nordfjaern/32/49124_2.png) [@Trond\_Nordfjaern](https://community.homey.app/u/Trond_Nordfjaern)\ **Post date:** [October 16, 2026, 11:22pm UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7417 "2026-10-16T23:22:12Z")
Did some more testing. I think I am able to reproduce the issue quite consistently now. The w600 heats up 2 degrees celcius more than the set point temp in zigbee mode (have not tested with Matter). E.g. in order to get 23 degrees in the room you need to set the temp to 21 in Homey (or directly at the valve). Offset is not at all relevant for this. You can hopefully reproduce or falsify by setting the valve to 22 and it will likely close at uncomfortable 24 degrees. This affects reliability in Homey as it shows that heating is turned off when it is not, and will give less comfort. If this is reproducable the app could compensate or we need to set temps 2 degrees below desired with the W600 in all flows (a somewhat dirty workaround). I for one would prefer the added reliability above what I suspect is a “battery-preserving feature” from Aqara. Hope someone else with W600 can reproduce this and I am in a good location to test app editions myself as we are in the heating season in Northern Scandinavia. ---
**Author:** ![Drako74](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/drako74/32/150506_2.png) [@Drako74](https://community.homey.app/u/Drako74)\ **Post date:** [October 17, 2026, 12:19am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7418 "2026-10-17T00:19:20Z")
> [@Trond\_Nordfjaern](#): > > When trying to add the device in the Aqara Android app it did not detect it automatically and tried to add the device both through matter code and QR. Never reached the mode switch that appared when the device came from the factory **Steps to Switch the Protocol** 1. **Initial Pairing (Thread mode):** - Pull the battery tab on the W600 to turn on the display. - Open the Aqara Home app (with Wi-Fi and Bluetooth enabled) and add the device, or pair it initially in its default Thread/Matter state. 2. **Factory Reset (if required): \<\<\*\*\*\*\*\*\*\*\*\*\*\*\*\*** - If you need to re-configure the device, press the device button 2 times and then hold it for more than 10 seconds to restore factory settings. 3. **Switch Protocol in App:** - Go to the accessory settings inside the Aqara Home app. - Locate the **Switch Protocol** option (or select the desired protocol—Zigbee or Thread—during the device setup/re-add flow). - Confirm the selection and wait for the configuration to apply When you have completed the indicated Factory Reset button press combination, you should then open the Aqara mobile application and if Bluetooth is enabled on your mobile device the app should automatically detect the W600 and switching protocol between Zigbee and Thread is just a couple of taps in the app and wait. The app guides you through the process. > [@Trond\_Nordfjaern](#): > > The w600 heats up 2 degrees celcius more than the set point temp in zigbee mode (have not tested with Matter). E.g. in order to get 23 degrees in the room you need to set the temp to 21 in Homey (or directly at the valve). Offset is not at all relevant for this. You can hopefully reproduce or falsify by setting the valve to 22 and it will likely close at uncomfortable 24 degrees > [@Trond\_Nordfjaern](#): > > I have set them to +2 offset and will observe them for a few days more and come back to you The most likely reason you are seeing the thermostat heating 2°C above the set temperature is because you have set the offset to +2°C. Please can you confirm what you are using to measure the room temperature, and where the measuring device is located? And that you are seeing this temperature discrepancy when the Homey device Advanced Settings Temperature Offset is set to 0 (zero). I only ask these questions because I have a couple of these W600 TRV’s and they have been rock solid reliable. ---
**Author:** ![Trond\_Nordfjaern](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/trond_nordfjaern/32/49124_2.png) [@Trond\_Nordfjaern](https://community.homey.app/u/Trond_Nordfjaern)\ **Post date:** [October 17, 2026, 12:23am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7419 "2026-10-17T00:23:38Z")
Thank you. I am not that concerned about changing over to Matter anymore as I do not think the issue lies there. The 2 degrees issue is there both with and without onset +2 (it was just something I intially tested). They are at 0 now and everything works (valves open and closes at the temps I want) @TedTolboom **when I have set temps 2 degrees below intended**. Did you try to set the valve to a temp and check that it closes at the set temp with zigbee (literally listen to the radiator and check valve status % in Homey in all its pure madness)? My hypothesis is that it will close at a temp which is about two degrees above the set temp, which is absolutely not fine as the room will be overheated and that Homey/the current Homey Aqara app will report that heating stopped way before it did. I am very happy to be proved wrong on this. ---
**Author:** ![CoonHouse](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/coonhouse/32/2764_2.png) [@CoonHouse](https://community.homey.app/u/CoonHouse)\ **Post date:** [October 17, 2026, 10:44am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7420 "2026-10-17T10:44:51Z")
Since lately (new release?) the AND cards for all my Aqara device only have the option “… Is on”. Is this an app issue or has it something to do with my Homey? Other users experiencing this problem? Thanks. ![Screenshot 2026-10-17 124053](https://us1.discourse-cdn.com/flex025/uploads/athom/original/3X/5/2/5242cf04759297cc1b30991b0854be622087e358.png) ---
**Author:** ![DirkG](https://sea1.discourse-cdn.com/flex025/user_avatar/community.homey.app/dirkg/32/118897_2.png) [@DirkG](https://community.homey.app/u/DirkG)\ **Post date:** [October 17, 2026, 11:26am UTC](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156/7421 "2026-10-17T11:26:31Z")
What conditions were in place before the “new release” (of what? Aqara app or Homey firmware?), that were provided by the Homey Aqara app for a contact sensor? [Previous page](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156.md?page=354) [Next page](https://community.homey.app/t/app-aqara-xiaomi-smart-home-simplify-your-life-with-a-smarter-home/156.md?page=356)